OVERLAP POOL LINERS: On this type of pool, the pool liner goes up and over the top lip of the pool wall. It then comes down over the edge on the outside of the pool. This type of pool liner is normally secured with some sort of clamping method that holds it in place. Any adjustment that may be needed on the wall height of the pool liner is made by removing the lamp(s) and either letting in or pulling out more of the liner.

BEADED POOL LINERS: Beaded pool liners come in 2 sizes, 48″ & 52″ wall heights. If there is any height adjustment that needs to be made, this needs to be done by removing or building up the height of the “cove” located at the base of the pool wall within the pool. Cove is available in “wedge” shaped Styrofoam or sand can be used by compacting it into the corner where the wall meets the floor.

UNIBEAD J-HOOK POOL LINERS: Uni-bead or J-Hook pool liners have a upside down J, and just hooks on the top side of the pool wall. J-Hook pool liners can also be cut to be used as a beaded receiver

Please note that this chart is to be used only as a guide since pool water
problems are often the result of several factors.

What Are Solar Sun Rings

The Solar Sun Ring is a passive solar swimming pool heating device made from two sheets of heavyweight U.V. resistant vinyl. The upper clear layer holds insulating air and focuses sunlight on the blue colored lower layer.

The blue layer absorbs about 50% of the sunlight and converts it to heat. The balance of the sunlight is allowed to pass through for deep water heating.

How Do Solar Sun Rings Work?

At night the contained air acts as an insulating blanket to retain heat gained during daylight. Solar Sun Rings are equipped with six magnets to improve clarity and decrease hardness of the water in your pool. The magnets are positioned to facilitate rafting. The strength of the magnets will permit single position removal but will easily separate to prevent entrapment in accidental falls.

Solar Sun Rings were designed to be compatible with automatic pool cleaners. In the event the suction hose catches on a ring, the ring will separate from the raft to allow the pool cleaner to continue. Neither water nor pool chemicals can evaporate through the Solar Sun Rings two layers of heavyweight vinyl.

You will save water and chemicals about equal to the percentage of the surface covered. Once the water in your pool has reached adequate temperature, Solar Sun Rings may be turned over to conserve water by limiting evaporation without significantly heating the water.

How Many Solar Sun Rings Do I Need?

We recommend enough Solar Sun Rings be purchased to cover 70% to 80% of your pools
surface, ignoring the small triangles between the rings.

Are Solar Sun Rings Compatible With My Pool?

Solar Sun Rings may be used on all chlorine or salt water system pools, whether in ground or above ground.

How Do I Clean My Solar Sun Rings?

After removal from the swimming pool Solar Sun Rings can be easily cleaned with a sponge and mild detergent solution.

Solar Sun Rings Help Your Pool Stay Clean

Your pool requires some direct sunlight and open water to stay healthy. The open water around the raft of Solar Sun Rings and the triangle caused by the convergence of three Solar Sun Rings is by design. These open areas allow your pool to receive some direct sunlight. This sunlight will greatly reduce the incidence of mustard algae.

INSTRUCTIONS
FOR USE

PROPER INFLATION IS NECESSARY TO USE THIS
PRODUCT INFLATION

INFLATION

Inner Grid:

The inner grid should be inflated orally with about two large breaths of air for an average person. Do not use more air, two breaths is all that is needed. Close the valve. Bunch up the SSR and move the contained air around to separate both layers of plastic. The SSR cannot be made to lie flat unless the layers are separated. The SSR should be about the size of a soccer ball when bunched up.

Outer Ring:

Inflate the outer ring orally until it is firm. Close the valve. Place each SSR single layer in direct sunlight on a flat non-abrasive surface until the packing lines relax. This should take from 30 minutes to 3 hours depending on the intensity of the sun. If the SSR does not lie flat after the packing lines are relaxed, examine the SSR for areas not separated. If the SSR still does not lie flat measure the diameter. A properly inflated SSR is 59 inches or 149.86cm in
diameter. If the SSR is smaller use the deflation tube provided to let air out of the inner grid until it lies flat. Excessive air in the grid section, deep packing lines and failure to separate both layers of plastic will all cause the outer edge to curl and distort.

HOW TO USE THE SOLAR SUN RINGS

HEATING: Once the Solar Sun Rings are inflated, cover up to 70% to 80% of the surface of your pool with Solar Sun Rings by placing the blue colored side on the water. You should not cover more than 70% of the surface on deep pools and not more than 80% on shallow pools. For the best solar effect, keep the upper surface of the Solar Sun Rings clean and clear.

COOLING:
Turn the Solar Sun Rings over so the blue side is up. The Solar Sun Rings do not heat water efficiently when upside down.

WATER AND CHEMICAL SAVING

Neither water nor chemicals can evaporate through the two layers of heavyweight vinyl. You will save on water and chemicals about equal to the actual percentage of water covered.

CARE OF SOLAR SUN RINGS

Once inflated proper care of this product will greatly extend its useful life. Pool decking is designed to be abrasive to prevent slips and falls. Do not walk on Solar Sun Rings or drag Solar Sun Rings on this abrasive surface. When Solar Sun Rings are not on the pool water do not stack them in direct sunlight, excessive internal temperatures will develop and melt the vinyl films.

Solar Sun Rings are passive pool heating devices and should not be used as pool toys.

Solar Sun Rings are warranted to be free of manufacturing defects for two years. Warranty is limited to materials and workmanship. Solar Sun Rings will not warranty products for damage or suitability.

The pool’s filtration system contains a pump and a filter system which circulates the pool water through the filter to remove dirt and contaminants and clean the pool water. A pool filter should run at least 8 hours daily to properly maintain the pool water’s clarity and cleanliness. A sand filtration system, the most popular and economical type, uses a bed of fine sand to trap contaminants and debris as the pool water circulates through the sand filter. Using sand as the filtering media provides some benefits to the pool owner. Sand filters are relatively simple to use and may be cleaned by backwashing to remove the accumulated debris. Sand is an inexpensive filter media and it is very long lasting. If properly treated, sand only needs to be replace once every 3-4 years. pcPOOLS offers sand filtration systems for both above ground and in ground pools. For parts of the country with water restrictions or for pool owners looking for even better pool water quality, another type of pool filter system is a cartridge filtration system. Cartridge filter systems use a replaceable pool filter to trap debris and other contaminants to clarify the pool water. Using a cartridge filter (which looks much like a large oil filter used in a car) provides increased benefits that sand can’t match. Because of the cartridge’s construction, it will trap smaller particles than sand making the pool water quality better. Cartridge systems are also recommended where water restrictions occur. Cartridge systems do not require “backwashing”, which can use hundreds of gallons of water. A cartridge filter is cleaned by removing the cartridge element and hosing it off and soaking it in filter cleaner for an hour or two. The cartridge may need to be replaced every season depending on the amount of usage of your pool.